Guide And Tips On How To Repair Computer And Troubleshoot Pc

Guide And Tips On How To Repair Computer And Troubleshoot Pc

Introduction

Computer problems can be upsetting. But most of them are minor and can be repaired easily, so don’t panic and take a deep breathe when pc problems happen to you.

Basic computer repair / pc troubleshooting tips and guide:

1. Check the power strip connection. Is the power indicator light lit? Make sure the power switch is turned on and to the correct AC voltage. Then shut down the power and check all the cables of your computer such as data cables, power cable, internal circuitry cables and cards if possible and devices like mouse, keyboard, monitor, etc. and make sure that everything is seated properly and working fine. You can push the cables or devices gently. Sometimes you need to actually unplug them from the computer and then plug in again.

2. When you notice a software or hardware error in your computer, try to find out what was changed before the problem occurred. In the meantime, you can google the error message and find a fix to the problem. The following are some common error messages and solutions:

a. “Non-System disk or disk error”: remove non-system diskette, USB, CD inserted before starting computer.
b. “Windows was not properly shut down. One or more of your disk drives may have errors on it. Press any key to run ScanDisk on these drives.”: Press the enter key and allow the machine to do a scan and fix the problems.
c. “Not enough memory / Insufficient memory”: Close some programs and try again.
d. “My monitor is black”: Check power and cable connection. Check if it is in sleep mode, especially laptop.
e. “No sound”: Check if the speaker is plugged into the wrong socket, MIC. Also check Mute? Volume?
f. “Computer freezes”: Try Ctrl+Alt+Del. If it does not work, force the computer to power off by keeping on pressing power key until the pc shuts down. Then wait for about 10-15 seconds and re-start computer.

3. Use the event viewer utility by going to Start –> Control panel –> Administrative tools –> Event viewer. By using this tool, you will find the error or warning messages associated with any faulty hardware or software.
4. Check the hardware settings in the device manage
1000
r of the system and make sure all the device drivers is up to date and working properly, that is, there is no error sign shown.
5. When you find a faulty component in your computer, you should check it with the other good computers so that you can make sure whether the component has problems or not before buying a new one.
6. If the above is ok and your computer still has problems, it might be the cause of virus or the registry / system files corrupted. You can find related tools to fix the problem. If the problem is serious, consider to re-install the Operating System. It is recommended that you create two partitions. One is for your OS and the other is for your data.
7. Finally, it is important to take a detailed note for future use.

Conclusion

When you try to repair a computer, it is important to find out what you did before and also your focus should be on power supply, video, mother board, CPU and the hard drive.

By: ray xu

Article Directory: http://www.articledashboard.com

To buy all CHEAP computer related products, please go to world top computer discount store

For more information about computer repair, please go to More tips on computer repair

Start your own LCD Monitor Repair work from the comfort of your own home. 

Tags:

Category: Computer Repair

Comments (6)

Trackback URL | Comments RSS Feed

  1. Jo Gabriel says:

    Thanks for this tips. When my computer is in trouble i usually check it with the other good computers so that you can make sure whether the component has problems or not before buying a new one.

  2. Well new to your blog, but I want to say it is full of great information and has been a source for a lot of what I am trying to do.

  3. hi. Thanks for these tips, your blog suggested me a lot in repairing my pc. All technical tips and suggestions that you have included in this blog had helped me in keeping my pc safe.

    Thanks!

  4. MrLoftcraft says:

    I have discovered a glitch that gives the blue screen of death for Windows XP. This is a hardware problem for old computers. If you have 2 Ram,DDram pieces on the motherboard, you should enter the Bios Setup utility and change the operating speed for your RAM. Set it from Auto to other speeds available but not the maximum speed. For example, if you have 800, 667 and 400 Mhz just choose 667 and you are off the hook.

  5. Austin,TX computer repair says:

    Our trusted home computer repair technicians will come directly to your home to solve your computer troubles right on-the-spot. Simply provide us with your details below so we can dispatch one of our highly skilled technicians to help resolve your computer related problem. We strive for same day service on all calls.
    http://austincomputerrepair.biz/

  6. Australia migration says:

    I m old user of your blog. but commenting very first time. I am computer hardware engg and running my own computer repair shop. Your blog helped me so many times to troubleshoot problems i have found in past. Thank you so much for you help support.i hope i will find solutions in future also.

Leave a Reply

WP-SpamFree by Pole Position Marketing